From both MRO Stock and MRO Electric, we sell New and Remanufactured A06B-6096-H208‘s, and offer a competitive Repair and Exchange Program.
Please call 1-800-691-8511 or e-mail [email protected] for a quote or for more information on Fanuc products and the A06B-6096-H208 alarm codes.
A06B-6096-H208 Alarm Codes
Alarm Code 1
(1)Meaning Inverter: internal cooling fan stopped
(2)Cause and troubleshooting
Fanuc 15i Alarms /Errors for CNC machinists. Fanuc 15i Alarms Program Errors/Alarms (P/S alarm) Program Errors /Alarms on program and operation (P/S alarm). Page 471B-63784EN-1/01 OPERATION 10.DISPLAY - Explanation of alarm messages For an explanation of the alarm messages reported by CNC self- diagnosis, refer to the FANUC Series 15i/150i-MODEL B Maintenance Manual (B-63785EN). For an explanation of external alarm messages, refer to the manual supplied by the.
(a)Check whether there is any foreign material in the fan.
(b)Check that the fan connector is attached correctly.
(c)Replace the fan.
(d)Replace the SVM.
Alarm Code 2
(1)Meaning Inverter: control power supply under voltage Maquina virtual mac no windows.
(2)Cause and troubleshooting
(a)Check the three-phase input voltage of the amplifier (the voltage shall not be lower than 85% ofthe rated input voltage).
(b)Check the 24 V power supply voltage output from the PSM (the voltage shall normally notnlower than 22.8 V).
(c)Check the connector and cable (CXA2A/B).
(d)Replace the SVM.
Alarm Code 5
(1)Meaning Inverter: DC link under voltage
(2)Cause and troubleshooting
(a) Check that the screws for the DC link connection cable (bar) are tight.
(b)If a DC link low voltage alarm condition occurs in more than one module, see Subsection 3.1.4,
“Alarm code 4” for explanations about how to troubleshoot the power supply module.
(c)If a DC link low voltage alarm condition occurs in only one SVM, replace that SVM.
Alarm Code 6
(1)Meaning Inverter: overheat
(2)Cause and troubleshooting
(a)Check that the motor is being used at or below its continuous rating.
(b)Check that the cooling capacity of the cabinet is sufficient (inspect the fans and filters).
(c)Check that the ambient temperature is not too high. (d)Replace the SVM. Error 0x8a010101 when activating office for mac.
Fanuc 15i-m Manual
Alarm Code F
(1)Meaning Inverter: cooling fan stopped of the radiator
(2)Cause and troubleshooting
(a)Check whether there is any foreign material in the fan.
(b)Check that the fan connector is attached correctly.
Permute mac os. (c)Replace the fan.
(d)Replace the SVM.
Alarm Code P
(1)Meaning Communication error between amplifier and module
(2)Cause and troubleshooting
(a)Check the connector and cable (CXA2A/B).
(b)Replace the control printed-circuit board.
(c)Replace the SVM.
A06B-6096-H208 Alarm Code 8
(1)Meaning Inverter: DC link current alarm
(2)Cause and troubleshooting
(a)Disconnect the motor power leads from the SVM, and release the SVM from an emergency stop condition.
<1>If no abnormal DC link current alarm condition has occurred. Go to (b).
<2>If an abnormal DC link current alarm condition has occurred. Replace the SVM.
(b)Disconnect the motor power leads from the SVM, and check the insulation between PE and the motor power lead U, V, or W.
<1>If the insulation is deteriorated. Go to (c).
<2>If the insulation is normal. Replace the SVM.
(c)Disconnect the motor from its power leads, and check whether the insulation of the motor or power leads is deteriorated.
<1>If the insulation of the motor is deteriorated. Replace the motor.
<2>If the insulation of any power lead is deteriorated. Replace the power lead.
Alarm Code 8.9.A.
(1)Meaning Inverter: IPM alarm
(2)Cause and troubleshooting
(a)Disconnect the motor power leads from the SVM, and release the SVM from an emergency stop condition.
<1>If no IPM alarm condition has occurred. Go to (b).
<2>If an IPM alarm condition has occurred. Replace the SVM.
(b)Disconnect the motor power leads from the SVM, and check the insulation between PE and the motor power lead U, V, or W.
<1>If the insulation is deteriorated. Go to (c).
<2>If the insulation is normal. Replace the SVM.
(c)Disconnect the motor from its power leads, and check whether the insulation of the motor or power leads is deteriorated.
<1>If the insulation of the motor is deteriorated. Replace the motor.
<2>If the insulation of any power lead is deteriorated.
Replace the power lead.
Alarm Code 8.9.A.
(1)Meaning Inverter:IPM alarm (OH)
(2)Cause and troubleshooting
(a)Check that the heat sink cooling fan is running.
(b)Check that the motor is being used at or below its continuous rating.
(c)Check that the cooling capacity of the cabinet is sufficient (inspect the fans and filters).
(d)Check that the ambient temperature is not too high.
(e)Replace the SVM.
Alarm Code bcd
(1)Meaning Abnormal inverter motor current
(2)Cause and troubleshooting
(a)Checking the servo parameters Referring to “FANUC ACSERVO MOTOR i series Parameter Manual (B-65270EN),” check whether the following parameters have default values.
Fanuc-15i PRM 1809, 1852, 1853
Fanuc 15m Manual
Fanuc-16i/18i/21i PRM & Power Mate i No.2004, 2040, 2041
Alternatively, if an abnormal motor current alarm condition occurs only on rapid acceleration/deceleration, it is likely that the motor is being used under too harsh a condition. Increase the acceleration/deceleration time constant, and see what will occur.
(b)Disconnect the motor power leads from the SVM, and release the SVM from an emergency stop condition.
<1>If no abnormal motor current occurs Go to (c).
<2>If an abnormal motor current occurs Replace the SVM.
(c)Disconnect the motor power leads from the SVM, and check the insulation between PE and the motor power lead U, V, or W.
<1>If the insulation is deteriorated Go to (d).
<2>If the insulation is normal Replace the SVM.
(d)Disconnect the motor from its power leads, and check whether the insulation of the motor or power leads is deteriorated.
<1>If the insulation of the motor is deteriorated Replace the motor.
<2>If the insulation of any power lead is deteriorated. Replace the power lead.
If you are still having trouble with the A06B-6096-H208 alarm codes and would like a replacement rush shipped, please contact us immediately.
Click Now to Visit our A06B0-6096-H208 Product Page
Instruction Manual and User Guide for Fanuc 15i. We have 35 Fanuc 15i manuals for free PDF download.
Fanuc 15i Manuals
CNC Programming, Operating & Maintenance Manuals
Fanuc Series 15i/150i-MB (Programming) Operators Manual B-63784EN/01
Fanuc Series 15i/150i-MB (Operation) Operators Manual B-63784EN-1/01
Fanuc Series 15i/150i-Model B Parameter Manual B-63790EN/01
Fanuc 15i Parameter Manual
Fanuc Series 15i/150i-Model B Maintenance Manual B-63785EN/01
Fanuc Series 15i/150i-Model B Connection Manual (Hardware) B-63783EN/01
Fanuc Series 15i/150i-Model B Descriptions Manual B-63782EN/01
Fanuc Serien 15i/150i-MA (Programmierung) Bedienungshandbuch B-63324GE/03
Fanuc Series 15i/150i-MA (Operation) Operators Manual B-63324EN-1/03
Fanuc Serien 15i/150i-MA (Bedienung) Bedienungshandbuch B-63324GE-1/03
Fanuc Series 15i/150i-Model A Parameter Manual B-63330EN/03
Fanuc Series 15i/150i-Model A Maintenance Manual B-63325EN/03
Fanuc Series 15i-16i-18i-21i Model A Remote Diagnosis Operators Manual B-63454EN/01
Fanuc Series 15i/150i-Model A Remote Buffer Descriptions Manual B-63322EN-1/01
Fanuc Series 15i/150i-Model A Descriptions Manual B-63322EN/03
Fanuc Series 15i/150i-Model A Connection Manual (Hardware) B-63323EN/03
Fanuc Series 15i/150i-MA (Programming) Operators Manual B-63324EN/03
Fanuc Power Mate i CNC Screen Display Function Operator Manual B-63164EN/08
FANUC Change of specification of 3MB SRAM module in S16i/18i/160i/180i/160is/180is-MODEL A and S15i-MODEL A/B Additional Manual A-73123EN-096/01
Fanuc Power Mate i Memory Card for 30i 16i 0i 20i 15i and Data Server Additional Manual A-80542E/07
Fanuc 15i Model B Maintenance Manual 63785EN
Fanuc 15i-Model A Remote Buffer Descriptions Manual 63322EN-1
Fanuc 15i-MB Operator Manual Programming
Fanuc 15i-Model A Connection Manual Function Vol-3 63323EN-1
Fanuc 15i-Model A Connection Manual Function Volume-2 63323EN-1
Fanuc 15i-Model A Connection Manual Hardware 63323EN
Fanuc 15i Parameter Manual
12»